Photonic Crystal Simulation
Photonic crystals are periodic structures that are designed to affect the motion of photons in a similar way that periodicity of a semiconductor crystal affects the motion of electrons. The non-existence of propagating EM modes inside the structures at certain frequencies introduces unique optical phenomena such as low-loss-waveguides, omni-directional mirrors and others. The part of the spectrum for which wave propagation is not possible is called the optical band-gap. The underlying physical phenomenon is based on diffraction. Therefore, the lattice constant of the photonic crystal structure has to be in the same length-scale as half the wavelength of the electromagnetic wave. Figure 1 shows a one dimensional periodic structure which is investigated by using the transient solver of CST MICROWAVE STUDIO® (CST MWS).
Figure 1: 1 dimensional periodic structure
The rods are made from GaAS with refractive index of 3.4 and with an edge length of about 180 nm. The lattice spacing between the rods is 760 nm. As a first step, the transmission of a plane wave through this crystal is simulated.
Figure 2: single column of the array
By using appropriate boundary and symmetry conditions it is sufficient to calculate a single column of this array as shown in Figure 2. In this case, the structure is driven by a waveguide port. Due to the magnetic and electric symmetry planes, the excitation mode is a normally incident plane wave.
Figure 3: Transmisson vs. wavelength
Figure 3 shows the transmission through the structure. Between 1400 and 2200 nm the transmission is zero. In this bandgap region no wave propagation in possible.
Figure 4: Wave Propagation at frequencies below the band gap
Figures 4-6 shows the propagation of a plane wave at normal incident for at different frequencies.
Figure 5: Wave propagation at frequencies in the band gap
Figure 6: Wave Propagation at frequencies above the band gap
The information obtained about the photonic band gap can be used to design optical devices. Figure 7 shows the periodic PBG structure as described above. A line defect is introduced and the structure is excited with a electromagnetic wave at band gap frequencies. The wave can only propagate inside the line defect.
Figure 7: Photonic Crystal with line defect
Finally, Figure 8 shows the wave propagation inside the Photonic crystal with a bent defect. Again, the structure is driven with a time harmonic signal. The signal frequency is inside band gap of the crystal. Consequently, the wave propagates inside bend defect.
Figure 8: Photonic crystal with a bend defect
This article demonstrates the possibilities to model photonic crystals with CST MWS by using the transient solver. The general characterization would also be possible with the Frequency Domain and Eigenmode Solver of CST MWS by applying periodic boundary conditions.
CST Article "Photonic Crystal Simulation"
last modified 15. Jan 2007 5:42
printed 7. Jan 2009 3:31, Article ID 296
URL:
All rights reserved.
Without prior written permission of CST, no part of this publication may be
reproduced by any method, be stored or transferred into an electronic data processing system, neither mechanical or by any other method.
Article ID: 296
Last modified: 15. Jan 2007 5:42
Other Articles
This article demonstrates the application of CST MICROWAVE STUDIO® (CST MWS) to the analysis of large reflector feed arrays. An array consisting of 19 elements was simulated but a larger array of more than 100 elements may also be simulated since the memory scaling with mesh cells in CST MWS is almost linear. The simultaneous excitation feature in CST MWS was applied to obtain farfield patterns in just a single simulation. A parameter sweep was also carried out to obtain the S-Parameters as a funtion of element feeding postion.
Read full article..
This article presents the results of a CST EM STUDIO™ (CST EMS) low frequency simulation of the TEAM Workshop Benchmark 7. The excellent simulation performance of the low frequency solver is demonstrated.
Read full article..
This waveguide filter has been simulated with CST MICROWAVE STUDIO® general purpose frequency domain solver applying a tetrahedral mesh.
Read full article..
In this article a single periodic open-ended waveguide phased-array antenna with a dielectric radome at its aperture of variable thickness is analysed. As a verification it is shown that the superposition of two independent plane waves shows the same field pattern as the one created by the unit cell model.
Read full article..
A multi-stage depressed collector for the "Rijnhuizen" Fusion Free-Electron Maser (FEM) is simulated with CST PARTICLE STUDIO™. The results are reproduced with permission of Pulsar Physics. See also M.J. de Loos, S.B. van der Geer, Pulsar Physics, Nucl. Instr. and Meth. in Phys. Res. B, Vol 139, 1997.
Read full article..